Need a new Galvanized Torsion Axle for your Boat Trailer? This Axle comes equipped with 5 lug (4.5 inch bolt spacing) Galvanized Idler Hubs and Posi Lube/Accu Lube Spindles with a grease fitting in the end. The axle fits I Beam Trailers with an outside width of 72 inches. This Boat Trailer Torsion Axle is great for Pontoon Boats, Center Console Boats or any other kind of Fresh Water or Saltwater vehicle thanks to its fully hot-dip galvanized construction. Replace your Leaf springs for good with this Torsion Bar Axle.
I Beam Trailer Frame Width Required for This Axle Size - 72-inch Wide Trailer Frames (I-Beam Construction) - Measured outside to outside
Torsion Axle Specifications:
- Hubface measurement - 86"
- Brake flange measurement - 80"
- Outside of torsion bracket - 74 1/2"
- Starting angle height (no load) - 4.26"
- Starting angle height (full load) - 2.04
- Torsion axle starting angle - 30 degree down
- 5 on 4 1/2" bolt pattern
- V Bend Style Torsion Axle with drain hole
- Grease-able spindle
- 4 Hole Brake Flanges for disc brakes
This Hot-Dipped Galvanized Torsion Axle ships with galvanized Idler hubs installed. The hubs and bearings are pre-greased with a lithium-based grease, but additional grease may be added after installation.
Galvanized Hub Specifications:
- 5 on 4 ½ inch Bolt Pattern
- 1 3/8 inch inner bearing, 1 1/16 inch outer bearing
- 1.72 inch inner diameter grease seal
- Hot-Dipped Galvanized
- 1.98 dust cap size, dust cap is included and has a removable rubber plug for easy access to the Spindles built-in Grease fitting.
If you need to replace the mounting hardware as well, either Click the Check Box for (4) I Beam Torsion Axle Mounting Bolts SS, or Go to 1/2 inch Diameter by 1 1/2 inch Long Stainless Steel Bolt and order the quantity you need (typically 4 total per axle.)
New Mounting Holes May need to be drilled in order to install the new axle.
These Axles can be used on Boat Trailers or Utility Trailers. Box Trailers, Car Haulers, Horse Trailers etc. can all benefit from the Torsion Arm System over leaf springs, and the Galvanized Coating will last even longer if the trailer isn't entering saltwater.
| PN |
Axle Type |
Rating |
Hub Face to Hub Face |
Mounting Bracket Center |
Brake Flange to Brake Flange |
Hub Type |
Finish |
Bearings |
| TTA009 |
Galvanized Boat Trailer Torsion Axle 3500 lb 5 Lug |
3,500 lbs. |
86" |
74-1/2" |
80" |
5 bolt on 4-1/2" Bolt Pattern (Pre-greased Hubs Included) |
Hot-Dipped Galvanized |
1-3/8" x 1-1/16" |
SELECTING THE PROPER TRAILER AXLE
When selecting an axle for your application remember to consider the following important specifications:
-
LOAD CAPACITY: the load rating of the axle must support the maximum gross vehicle weight rating. For multiple axle trailers divide the GVWR by the number of axles to determine the minimum load capacity of each axle.
-
TRACK LENGTH: measure your axle track length by determining the distance between the center of one tire to the center of the other tire. A more precise measurement can be made by measuring the distance from one 'HUB FACE' to the other. The hub face is also known as the mounting surface where the wheel studs are located.
-
SPRING CENTERS: measure the distance from the center of one spring to the center of the other.
NOTE: not required for replacement torsion axles
-
OVERALL LENGTH: measure the distance from the very end of an axle's spindle to the very end of the opposite spindle.
-
AXLE STYLE: important when reusing old mounting hardware and also for proper tire clearance. Includes straight axles (round or square), drop axles with offset spindles, and torsion axles. Also consider spindle size when reusing existing hubs or drums.
-
AXLE CAMBER: Most trailer axles are designed with a bend in the tube that will deflect when the load (weight of the trailer) is applied. This will theoretically bring the trailer wheel camber toward a 0 value that is the best setting for most trailer applications. This will allow the tires to wear evenly and allow the longest tread life. Camber can be affected by damage to the axle. For example, if the axle spindle is bent, this will usually cause a negative camber on that side which will cause excess tread wear on the inside of that tire.
How can I tell between a torsion axle and leaf spring axle?
If you have spring axle suspension your trailer will have leaf springs. Your suspension should look similar to this:
If you have torsion axle suspension your trailer will look similar to this:
What are the pros and cons of a leaf sprung axles and torsion axles?
Both torsion and suspensions have a record of reliability. There are advantages and disadvantages to both, but it comes down to your preference because they both work great in their own way.
Torsion axles are made up of thick rubber cords concealed in the axle's tubing. As each wheel moves up and down, the rubber cords compress offering an even wheel suspension for a smooth ride. Each wheel acts independently, moving and absorbing shocks.Torsion axles are mounted directly to the frame which means fewer moving parts compared to spring suspensions, resulting in a smoother shock action. This stiffens the frame, reducing flex.
This system is also less likely to corrode because the axle tube is galvanized inside and out. There are no metal-to-metal action like springs, so bare metal isn't exposed, preventing corrosion. There are fewer working parts in a torsion suspension, therefore less maintenance is required.
The disadvantages of torsion are they are more expensive than spring suspensions and more expensive to repair or replace. There is also no impact distribution, so if you hit a curb, the full impact is on one wheel or set of wheels.
Leaf springs have been used for centuries and have proven to be solid performers. This is the most widely used suspension system due to its affordability. Spring suspensions are the most dependable for even tire wear and a steady ride, especially in multi-axle applications. Leaf springs better absorb the load from uneven ground or shock from a pothole. Each tire has its own set of springs. If you have to store your trailer on uneven ground, the independent wheel suspension means the trailer will hold up better over time. Spring suspensions are cheaper and easier to repair compared to torsion suspensions.One con of springs is the metal-on-metal design can lead to faster wear, leading to more frequent repairs. Spring suspensions also tend to be a bouncy ride with an empty load or on uneven, rough roads.
Ningbo Harsco Machinery Co., Ltd is a professional manufacturer of trailer parts in Ningbo, Zhejiang Province, China since 2016.
We can produce many trailer parts & accessories as follows: Towbars, axles, brake drums, hubs, brake disc, bearings, springs and springs and suspension kits, couplings, mudguards, U-Bolts, Jockey Wheels, keel rollers and brackets, wobble roller, wheel spacer, equalizers and all accessories related to trailers.
If you can send me the drawings or specifications of the trailer parts, mechanical parts and wheels, we can give you our price.
Q1: Do you have factory?
A: Yes, we have our own factory, own engineers, we can meet custom's unique requirement.
Q2: Can I have a sample order?
A: Yes, welcome sample order to test and check quality. Mixed samples are acceptable.
Q3: It's OK to print my logo on your product?
A: Yes, we can according to your exact requirement.
Q4:How do you ship the goods and how long does it take arrive?
A: We usually shipped by DHL, UPS, FedEx, it usually takes 3-5 days to arrive. Airline and sea shipping also optional.
Q5: What is your advantages?
A: We are professional supplier for more than ten years, we always put the quality and price at the first place. At the same time, our products are exported to various countries, we have full experience to solve thorny problems.
If you want to know about our products and us, welcome to enquiry and email me.thanks
1-Welcome OEM
- You can use your own brands or ours, if you use our brand, our professional team will help you design the packing.
2-Our service
- You inquiry related to our products or prices will be replied in 24 hours.
- Well-trained and experienced staffs to answer all your enquirys in fluent English.
- Protection of your sales area, ideas of your design and all your private information.
- We have a QC team, every product will be checked by them before packed.
3-Welcome to visit
- When you come to our company visit us, we will arrange a car for picking up and help you book hotel. If you want to visit the local scenic spot, our colleague will accompany you.
4-Warranty
- Customer should be provide the video and the pictures for the problem products.
- Products returned within the warranty period must bear product number & date code.
5-After service
- In production and after delivery, we will track on time and tell you goods situation.
- When the goods arrived, if you find any design and quality questions, or difference from your samples, please feel free to contact us, we will find the question and solve it with you.
Audited Supplier 
){kind=link}
){kind=link}